CL2200/T66/T44/T22/LS1800/LS1600 Troubleshooting

• The bidet is in Sleep Mode.
  
  
• The Seat Sensor is not activated.
  
  
• The water supply is not open. 
  
  
• The Mesh Filter is clogged.

1. Turn off the water supply and disconnect the hose from the bidet.
   
   
2. Remove the mesh filter from the water inlet and clean it as needed to clear any clogs. Refer to the Maintenance section of your Owner's Manual for instructions. Reinstall the Mesh Filter and hose once complete.
   
   
3. Check your water supply valve under the toilet to ensure it is fully open.
   
   
4. Make sure water is flowing to your bidet by using the "Nozzle Cleaning" button.
   
   
5. Check if your bidet is in sleep mode:
   1. To enable/disable sleep mode, press and hold the “Deodorizer” button for 3 seconds and test the bidet again.
      
      
6. Complete a factory reset.

   1. Find the "Stop" button on your remote/arm control.

   2. Press the "Stop" button 4 times within 2 seconds.

   3. A 3-toned beep will sound and the remote will flash briefly, indicating the reset is complete.
      
      

7.  Take a seat on the bidet and try to start a wash cycle.
   
   

If a wash still does not start or water does not flow from your bidet after performing the above steps, please contact Brondell Customer Support using our Contact Form.

• The water supply is not open. 
  
  
• The Mesh Filter is clogged.
  
  
• The highest pressure setting is not selected.

1. Turn off the water supply and disconnect the hose from the bidet.
   
   
2. Remove the mesh filter from the water inlet and clean it as needed to clear any clogs. Refer to the Maintenance section of your Owner's Manual for instructions. Reinstall the Mesh Filter and hose once complete.
   
   
3. Check your water supply valve under the toilet to ensure it is fully open.
   
   

If you are still experiencing low-pressure issues after performing the above steps, please contact Brondell Customer Support using our Contact Form.

• The T-valve washer was not installed.
  
  
• Teflon tape was not applied during installation.

For T-valve and hose leaks:

1. Turn off the water supply and disconnect the fittings of the leaking part.
   
   
2. Check the washers to ensure they are not damaged or missing.
   1. If they are damaged or missing, please contact Brondell Support for further assistance.
      
      
3. Clean the fittings appropriately and remove old Teflon tape.
   
   
4. Apply 1-2 layers of new Teflon tape to the leaking fitting.
   
   
5. Slowly turn the water back on and check for leaks.

If the leak persists or you are experiencing a leak coming from the bidet itself, please contact Brondell Customer Support using our Contact Form.

If you are out of your product's warranty, you can find replacement hoses and T-valves using the links below.

• Swash Replacement Hoses
• Swash Replacement T-valves

• The bidet is not correctly installed.
  
  
• The seat or lid has been forced down instead of allowing it to close slowly on its own.
  
  
• The bumpers are not making contact with the toilet. (the toilet is not level)
  
  
• The bidet has been installed on a toilet that is too big or too small for it. 

• The seat or lid has broken.
  
  
• The internal slow-close dampener has failed.

• Home or beauty products have been left in contact with the seat.

We suggest cleaning your bidet's seat with a 50/50 mixture of water and rubbing alcohol, or using Dawn dish soap or Simple Green cleaning solution for future preventative care.

Please contact Brondell Customer Support using our Contact Form.

• The dryer flap is stuck closed due to a buildup of grime.
  
  
• The Seat Sensor is not activated.

1. Using a 50/50 mixture of water and rubbing alcohol, or using Dawn dish soap or Simple Green cleaning solution with a Q-tip or soft cloth, clean the dryer flap and dryer port.
   
   
2. Complete a factory reset.

   1. Find the "Stop" button on your remote/arm control.

   2. Press the "Stop" button 4 times within 2 seconds.

   3. A 3-toned beep will sound and the remote will flash briefly, indicating the reset is complete.
      
      

3. Sit down and start a dry cycle, check if there is any airflow.

If the issue persists, and there is no airflow, please contact Brondell Customer Support using our Contact Form.

• Grime has built up in the dryer port.

Using a 50/50 mixture of water and rubbing alcohol, or a cleaning solution such as Dawn dish soap or Simple Green, and a Q-tip or soft cloth, clean the dryer flap and dryer port.

• Eco Mode is turned on.
  
  
• The seat heater is not on the highest setting.

1. Turn off Eco Mode or, if you wish to continue using Eco Mode, wait 3-5 minutes after being seated for the seat to heat back up to the desired setting.
   
   
2. Complete a factory reset.

   1. Find the "Stop" button on your remote/arm control.

   2. Press the "Stop" button 4 times within 2 seconds.

   3. A 3-toned beep will sound and the remote will flash briefly, indicating the reset is complete.
      
      

3. Confirm you have set the seat heater to the highest setting.

If the issue persists, please contact Brondell Customer Support using our Contact Form.

• The remote is not paired.
  
  
• The batteries have died.

1. Check the batteries and replace them as needed.
   
   
2. Re-pair the remote to the bidet:

   1. Unplug the bidet and remove the batteries from the remote.

   2. Plug the bidet back in.

   3. Install the batteries in the remote within 5 minutes of the bidet powering on.

   4. You should see the blue circular LED around the stop button illuminate for 7 seconds. Push STOP on the remote while it is still illuminated. A jingle will play confirming the remote has been paired.
      
      

If the issue persists, please contact Brondell Customer Support using our Contact Form.